Mavic carbon road wheels: lightness, stiffness and efficiency

It all depends on your main terrain and your style.

• Hills/passes/sprints: a lighter rim and a responsive wheel set promote acceleration and changes of pace.
• Flat terrain/long fast rides: a taller profile provides aerodynamic benefits at steady speeds.

The right choice is not extreme: look for a balance between weight, stability and rigidity that you can use on your usual routes.

No. Excessive rigidity can make the wheel more demanding (less forgiving, more "harsh"), especially on rough roads. The goal is useful rigidity: rigidity that provides precise steering and good power transfer without compromising comfort or road holding. At Mavic, we aim for a consistent compromise between rim, spokes, tension and hub.

The internal width determines the actual volume of the tyre, its shape and therefore its grip, rolling resistance and stability. A wider rim often allows you to ride with slightly lower pressure for the same cross-section, for greater comfort and control without feeling vague. But be careful to check that this is compatible with your bike.

Tubeless tyres offer the following main advantages:

• Fewer punctures due to pinch flats (no inner tube)
• Better tolerance on poor road surfaces (optimised pressure)
• efficiency and comfort when the tyre/rim combination is well matched

The secret is not that "tubeless = magic", but rather correct installation, the right tyre, and maintaining the correct pressure.

Two common mistakes:

• Overinflating "by reflex" → loss of grip, fatigue, reduced performance on rough roads
• Underinflating without sufficient volume → unstable support, risk of tyre detachment (depending on the system)

The correct pressure depends on your weight, the section, the internal width, whether you are using inner tubes or tubeless tyres, and the condition of the roads. A well-designed wheel performs best when the pressure and volume are consistent.

IMPORTANT, when fitting tubeless tyres, it is very important to observe the maximum recommended pressure indicated on the wheel in order to avoid damaging it.

Golden rule: gentle rinsing, neutral soap + drying.

Avoid using a high-pressure jet on the bearings. Clean the rim and the areas around the spoke heads. Then, visually check for impact, chips, cracks or abnormal friction. Simple but regular maintenance significantly extends the lifespan.

If you ride more than 100 km per week, keep an eye on:

• play (wheel wobbling sideways)
• rotation (rough/noisy bearings)
• freewheel body (noise/sticking, irregular engagement)

If you wash your bike often, this is even more important: water and aggressive detergents shorten the life of bearings. Regular checks prevent "small noises" from becoming "big problems".

Three warning signs to look out for:

• intermittent rubbing on the brake/disc
• a feeling of "pumping" or the wheel no longer being stable when dancing
• rattling/metallic sounds (spoke that has lost tension)

A simple check: spin the wheel, observe the gap, then check the tension "with your finger" (comparative) and the tightness/condition of the spokes. A high-end carbon wheel should remain stable; if it moves, it is best to diagnose the problem early.

Two key points:

When cornering: favour a gradual lean and consistent tyre pressure. Carbon wheels offer a high degree of precision.

When braking (rim or disc brakes): anticipate, brake gradually and release before entering a sharp bend. On long descents, avoid "dragging" the brake continuously: it is better to use controlled sequences (slow down/release) to keep the system stable.

With tubeless tyres, performance comes not only from the equipment, but also from the right pressure setting.

If the tyre is overinflated, you lose grip and comfort; if it is underinflated, you compromise stability when cornering and increase the risk of skidding or even blowouts in extreme cases.

It is important to follow the minimum and maximum inflation guidelines indicated on your wheel.

To ride safely and get the most out of your tubeless carbon wheels:

• Follow the pressures recommended by the wheel/rim manufacturer (limits and compatibility).
• Follow the pressures recommended by the tyre manufacturer (min/max and tubeless mounting).

In practice, follow the strictest rule: never exceed the lowest maximum pressure between the two, and do not go below the minimum pressures indicated, where applicable. This is the basis for reliable assembly and consistent performance.